ICOM is a global network of independent advertising and marketing agencies, bringing people closer to brands through connected thinking. ICOM Network Marketing and Advertising Nederland, Colorado 369 followers Global alliance of 80+ independent advertising & marketing communication agencies in 60+ countries, ready to help you.

• Icom Network & Wireless Cards Drivers

How to configure ICOM, ENET, K+DCAN cable? What’s the difference? Here, BMW ICOM cable config manual:

Part 1: BMW ICOM configuration manual

Part 2: ENET cable configuration manual

Part 3: K+DCAN USB cable configuration manual

1 Install patched Ediabas 7.3 from the loader menu and reboot your computer

2 Set up your Ethernet adapter as shown below

3 Disable your antivirus, firewall and turn off WIFI

4 Connect ICOM to car and PC. Wait for a minute or two

5 On loader main screen, click on the relevant brand button for your car/motorcycle. ISTA-P will now launch

6 Select your ICOM in connection manager

1 Install patched Ediabas 7.3 from the loader menu and reboot your computer

2 Set up your Ethernet adapter as shown below

3 Disable your antivirus, firewall and turn off WIFI

4 Connect ENET cable to car and PC. Turn on ignition and wait for a minute or two.

5 Click on the “ENET ICOM emulator button”. ZGW search will open

6 Enter your car’s ZGW IP and click on “Continue”. Then wait for emulator running notifications to appear

7 On loader main screen, click on the relevant brand button for your car. ISTA-P will now launch

8 Select ENET in connection manager

Note: when ISTA/P asks for ignition ON/OFF during programming use the K15 controls located in the notification area of the taskbar (or the Hotkeys). This must be done in conjunction with the actual car ignition. Default setting is “ON

1 Install patched Ediabas 7.3 from the loader menu and reboot your computer Driver downloads for windows 7.

2 Install your K+DCAN cable and set COM port to COM9. Set latency timer to 1. Reboot your computer

3 Run K+DCAN network configuration tool from the loader menu (may take up to 30 seconds to complete)

Then check in network connections that the USB network connection has appeared

Note: if the network config tool does not work correctly, use the procedure below (mainly applies to non-English systems)

a- Rename the newly created adapter to USB and disable

b- Right click on USB->properties. Select Internet Protocol Version 4 (TCP/IPv4)>properties

c- Manually change IP to 169.254.0.8 and subnet mask to 255.255.0.0>ok>close

4 Disable your antivirus, firewall and turn off WIFI

5 Plug in your K+DCAN cable to car and PC.

6 Click on the “K+DCAN ICOM emulator button”. Then wait for emulator running notifications to appear

7 On loader main screen, click on the relevant brand button for your car. ISTA-P will now launch

8 Select K+DCAN in connection manager

Note: when ISTA/P asks for ignition ON/OFF during programming use the K15 controls located in the notification area of the taskbar (or the Hotkeys). This must be done in conjunction with the actual car ignition. Default setting is “ON”.

This is all about network connection (wired or wireless) setup for ICOM A2 diagnosis with ISTA+ or programming with ISTA/P. All situations you may encounter are solved here.

*****Part 1 Wired connection when ISTA-P programming

it’s better to use Lan cable to connet to network instaed of wifi, for wifi is not stable sometime and cannot start programs ISTA-P (ISS-NEXT)

how to connect to network via Lan cable?

method 1: PC – router – ICOM

connect PC to the router, then connect ICOM to router

method 2: ICOM – PC

directlt connect ICOM emulator to PC

*****Part 2 Wireless/WiFi connection when ISTA+ diagnostics

you can use wifi during diagnosis with ISTA+. but sometimes, the connetion will be cut off automatically and program prompts you to continue connection

Wlan settings

go to ICOM Configuration Manger, and select Wlan settings-> Security type:WPA2 personal. the password should be the same with that of router. then save data and unplug and re-plug the Lan cable to connect to icom. it is impossible to diagnose via wifi if password is not set

(NOTE: this is not for USB WiFi; USB wifi comes with password and router setup)

what to do if WIFI fails to connect?

go to VCI settings, then select “HO-ICOM/NET”, NOT Ediabas

open Itool Radar to change ICOM IP address

find out IP address: 192.169.68.119

then go to “Confort Module” to change ip

Done! WIFI connection success.

This is fromobdtool: Best car diagnostic tools for salewebsite Auto Diagnostic Tools technical support

Icom Network & Wireless Cards Drivers